How far may a bundle extend past its end arms?

Overhang depends on stiffness, weight distribution, and the support arrangement. Provide the longest and shortest stored lengths so end support can be evaluated instead of assigning a universal allowance. West River Drive building-material dispatch should account for the bundle ends as it leaves storage.

Can round pipe rest on ordinary flat arms?

Round material requires a reviewed restraint approach. Arm configuration and suitable end stops should match the load, and operators should not depend on packaging alone to prevent rolling. For Alpine Ave receiving, describe whether pipe arrives loose or in restrained supplier packs.

Where should Comstock Park receiving stage long loads?

Use a defined staging area outside the rack approach and dispatch travel path. Its size should reflect the received bundle and the handling movement, not just the floor space beneath it. A West River Drive layout should reserve this space before counting permanent long-stock positions.

Does adding arms always increase usable capacity?

No. Upright and base limits still apply, and added levels can reduce the clearance needed for forks. Recheck the complete configuration before treating extra arms as extra storage capacity. In a mixed-freight Alpine operation, preserve fork clearance rather than filling every available elevation.

Comstock Park, Michigan

Cantilever Rack in Comstock Park, MI

Cantilever rack helps Comstock Park building-material operations separate long bundles from the dispatch floor. Projecting arms connect to uprights with no front columns across the loading face, allowing material to enter from the side instead of fitting inside a pallet bay.

We approach this as a handling decision before a storage count. Long bar, pipe, tube, lumber, and sheet loads can occupy the same department while needing very different support. A cantilever storage rack must accommodate those differences without making every retrieval a rearrangement exercise.

(616) 344-5683

Cantilever rack details that protect dispatch space

A row is only useful if a loaded truck can leave it. We map the approach, withdrawal, and turning movement separately from the standing load footprint. Side-loader access can change the aisle calculation considerably, while a conventional forklift may need additional room for the ends of a long bundle to sweep.

Outdoor placement calls for exposure-appropriate components and finish, with the supporting surface reviewed for the proposed installation. Indoor placement may be preferable for moisture-sensitive material. Neither option removes the need to understand how the stock will be picked during normal receiving activity.

Area services Long-load systems Gravity pallet storage Deep-lane alternatives

Pipe packs requiring side access

Lumber bundles with varying withdrawal quantities

Call (616) 344-5683

Why cantilever rack separates lengths from pallets

Selective rack organizes loads within beam spans and suits palletized goods that remain supported by their pallets. Open arms instead let overlength stock cross several uprights without a front post interrupting access. The two approaches often belong in neighboring zones rather than competing for one universal layout.

Arm spacing must follow the material, especially where a bundle becomes less stiff as pieces are removed. Sheet loads may require suitable decking or additional support. Specify the smallest usable bundle as well as the largest receipt so the final few pieces do not become floor stock.

Keep bundle ends clear of dispatch turns.

Check partially depleted packs for unsupported sag.

Reserve operating room beyond the steel footprint.

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Long material north of Grand Rapids

The West River Drive industrial corridor and Alpine Ave NW frame the local discussion in Comstock Park. Building-material storage needs a deliberate route away from outbound staging, particularly where mixed freight shares receiving space. Arm levels can group pipe separately from sheet packs, while row orientation helps keep a long-load turn outside a dispatch approach. These are planning considerations to verify on site, not assumptions about any particular facility.

Building-material distribution

Mixed-freight warehousing

Long-product order assembly

How cantilever racking moves from measurements to layout

The design conversation follows the load from arrival through selection. These four decisions provide a practical basis for comparing arrangements.

Identify the receiving unit

Note bundle dimensions, maximum weight, strapping, and fork access. Distinguish supplier packs from the smaller quantities staff actually return to storage after an order is picked.

Resolve arm projection and rating

Select arm length around load depth, then confirm its rated capacity for the intended loading condition. Include upright, base, and total system limits in the review rather than relying on an isolated arm figure.

Allocate one or two faces

Single-sided rows suit a boundary when the base and access fit. Double-sided rows serve two aisles, so assess both picking faces against dispatch movement before counting the added positions.

Plan installation boundaries

Agree which area can be released and how stored material will remain accessible elsewhere. We manage experienced installation crews and coordinate their work with the layout rather than assuming an empty building.

Recent Installations

Racking projects completed for warehouses across West Michigan.

View More Projects

Get the operating assumptions into the proposal

As a division of Warehouse Equipment & Supplies Co., Grand Rapids Pallet Rack brings a supplying and installing history dating from 1997. For a cantilever rack discussion, send your load list and a marked floor sketch. Call (616) 344-5683 so we can identify the measurements still needed before an arrangement is settled. (616) 344-5683.