How much height should I reserve above each bundle?

Reserve enough for the equipment to lift and withdraw that load without striking the next level. The required clearance depends on bundle height, fork approach, and lifting method. Do not calculate levels from product height alone. Older Holland plant interiors need that movement checked below actual overhead obstructions.

Can a sheet pack rest on the same arms as solid bar?

Only if the specified support arrangement suits both loads. Sheet packs may need closer support or an appropriate supporting surface to limit bending. The heavier item is not automatically the more demanding support case. For furniture production near 48th Street, show sheets after a partial pick as well as full packs.

Is side-loader access different from forklift access?

Yes, the loaded travel and placement movements differ. A side-loader may travel lengthwise with long material, while a conventional forklift often needs a larger turning envelope. Compare the specific vehicles rather than assuming either one fits a standard aisle. At a Waverly Road production site, test the route from receiving to the cutting area with material aboard.

Can we keep palletized supplies beside the long-stock area?

Yes, provided each load uses a suitable system and the combined layout maintains handling access. Selective positions can serve palletized supplies while open arms carry long inputs. Include both traffic patterns when reviewing the floor plan. James Street replenishment should keep long maintenance stock distinct from palletized production supplies.

Holland, Michigan

Cantilever Rack in Holland, MI

Cantilever rack gives Holland manufacturers a way to hold lengthy production inputs without front columns blocking access. Uprights carry projecting arms, allowing pipe, bar, tube, lumber, and sheet bundles to rest across the supports rather than inside pallet-sized openings.

Production storage works best when the support pattern follows the material. Thin sheet packs can deflect differently from rigid bar bundles, while partial lumber packs may change shape as pieces are removed. Cantilever racking should be specified around these working conditions, not just a photograph of a full load.

(616) 344-5683

How cantilever rack planning follows the production route

Start at receiving and trace the load to its next operation. Each decision should preserve a practical way to put material away and retrieve it.

Capture full and partial loads

Measure the largest incoming bundle and describe the smallest remaining pick. Record weights, lengths, packaging, and whether loose pieces can shift during handling.

Resolve the support geometry

Select arm depth and upright spacing together. Verify capacity at each arm and consider how a flexible load shares its weight across multiple supports.

Test the lifting approach

Use forklift or side-loader dimensions with the actual product aboard. Check lift reach, withdrawal clearance, and the turn toward the production area before assigning aisle widths.

Coordinate the assembled system

Confirm bases, bracing, arm elevations, and row positions in the proposal. We supply new material and use experienced installation crews we schedule and manage for assembly.

Cantilever storage rack arrangements for plant interiors

An older plant with 18–24 feet of building height may have less usable storage height after overhead obstructions and handling clearance are measured. Single-sided rows can occupy perimeter space; double-sided rows can divide a larger material area when access on both faces is maintained.

Outdoor storage requires its own exposure review, including finish selection and loading conditions. For an indoor row near a frequently opened door, winter loading exposure still matters: wet bundles, tracked-in moisture, and staging practices belong in the discussion even though the structure sits inside.

Holland service overview Long-material system overview Compare gravity-fed pallet lanes Review deep-lane pallet storage

Long feedstock stored near cutting areas

Mixed pipe sizes requiring direct selection

Sheet packs kept off working aisles

Call (616) 344-5683

Why cantilever racking can complement pallet positions

A selective system suits palletized ingredients, cartons, and finished components. It does not necessarily suit long unpalletized inputs that need side access across several arms. Keeping those storage duties distinct helps prevent a long bundle from occupying travel space intended for pallet handling.

Along 48th Street industrial and Waverly Road, manufacturing layouts can place raw stock near fabrication or assembly work. In food-processing buildings, long maintenance pipe and fabrication material may warrant a separate storage area from packaged inputs. The intended workflow, not the industry label alone, determines the row location.

Open loading face across multiple supports

Arm length selected for bundle depth

Aisles checked with the longest load

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Lakeshore receiving with plant constraints

US-31 and I-196 connect Holland receiving operations with regional material movements. At James Street corridor facilities, receiving space may also serve production replenishment, so a proposed row should leave room for incoming bundles awaiting inspection. Separate that temporary staging footprint from the permanent storage count before comparing layouts.

Furniture and component manufacturing

Food-plant maintenance departments

Energy and consumer-product fabrication

Recent Installations

Racking projects completed for warehouses across West Michigan.

View More Projects

Start with the production material

Share the material list and a sketch of the production handoff for a cantilever rack review. We operate as a division of Warehouse Equipment & Supplies Co. and have supplied and installed storage systems since 1997. The conversation can focus on which handling steps the layout should preserve. (616) 344-5683.